A level wet room walk in shower tray complete with a Dallmer fast flow drain and choice of 5kg liquid based (no mixing required) tanking kit, either PCI Lastogum or Weber Sys Protect. The perfect solution for installing a wet room or Walk in Shower.
| Suitable for: | NOT Suitable For: | ||
| Wooden or Concrete Floors |
| Vinyl Floor Finish |  |
| Tiled Floor Finish |
| Wheelchair Use | |
| Under Floor Heating |  | ||
| Walk In Showers |
|
Have a question about the WetBase or fitting it?
If you have a question about the WetBase or the fitting of it please see the following help articles:
Choosing the Correct Wet Room Tray
WetBase Shower Tray FAQ's
WetBase Shower Tray Fitting Instructions
Wet Room FAQ's
If you cant find an answer to your question in the above documents, or need further help or advice, please give our experts a call on 0800 280 8008, use the live chat function (in the bottom right corner) or send an email to This email address is being protected from spambots. You need JavaScript enabled to view it.
Optional Shower Screen:
We can also supply this wet room kit with an optional, quality, 8mm thick, 2000mm wide, toughened glass shower screen panel which is available in a selection of sizes.
The shower screen is finished with an easy clean coating as standard and comes complete with wall fixing channel and bracing bar.
•1200 x 800 x 20mm
•OFFSET Drain Position
•Pre-made 2% fall to drain
•Lightweight & Strong
•Under-boarding of WetBase required to provide support
•Complete with drain and choice of tanking kit
•Fully trimable by up to 50mm off each edge (equal amounts must be trimmed from each side)
•Ideal for creating flush 'walk in' showering areas (rest of floor will require boarding by 10mm)
•Easy & quick to install: WetBase installation instructions
•Designed and manufactured in the EU
•20 years guarantee if fitted in accordance with manufacturer’s instructions.
•FREE next working day delivery if ordered by 3pm (Terms & Conditions apply)
•Money back guarantee if not 100% happy (
Tanking / Waterproofing Kit:
The tanking kit is a ready-mixed, under-tile tanking system to protect water sensitive substrates from exposure to water. Suitable for wet areas not exposed to pressurised water, such as bathrooms, showers in residential buildings, hotels, old people's homes and hospitals.
Ready to use, no mixing required and easy to apply with a roller.
The kit includes a high performance joint reinforcing tape to protect against movement in floor joins and corners etc.
The contents are all INSIDE the bucket and the contents are protected in the bucket with polystyrene infill's to stop transit damage.The instructions are printed on the rear of the tanking kit.
For instructional video on the preparation and waterproofing (tanking) of your wet room or walk in shower see: Tanking-a-Wet-Room
The followings are the instructions for installing the Wetrooms Online WetBase (standard) on a wodden floor. These instructions and others for concrete floors and the Linear WetBase can be printed and / or downloaded in PDF format here:
Standard WetBase Installation (Wooden Floor)
Standard WetBase Installation (Concrete Floor)
Linear WetBase Installation (Wooden Floor)
Wetrooms online WETBASE low profile shower trays are designed to create a flat walk in shower area without raised steps or platforms. This tray is designed to be inset into or on top of WOODEN floors and then tiled over.
The Coated shower tray is pre machined with the correct falls in all directions to the drain which is partly attached to the tray.
It requires additional support which is achieved by fitting plywood panels between the joists.
Conventional floor boards are approx 20mm thick so laying the tray on top of the joists would bring the top of the tray level with the floor boards.
WE DO NOT recommend tiling straight on to floor boards. We recommend that the entire wooden floor is covered in a 10mm thermal tile backer board prior to tiling and therefore you may need to insert a 10mm packer under the wetbase
1 x 1200 x 800 under tray 20mm deep 2% fall.
1 x Drain with stainless steel grid (horizontal)
Fitting Instructions
1 x 5KG Tanking Kit, PCI Lastogum OR Weber Sys Protect:
| PCI Lastogum | Weber Sys Protect |
| 1 x 4KG PCI Lastogum tanking liquid | 1 x 4 kg weber.sys protec tanking fluid |
| 1 x 1 Litre Primer Liquid | 1x 1 kg weber PR360 primer |
| 1 x 10 metre tape for wall and floor joints | 1 x 10m BE14 tap |
| 2 x Pipe Collars |
A quality 8mm thick by 2000mm high toughened safety glass shower screen in a choice of widths, finished with an easy clean coating as standard, comes complete with wall bracket and support arm.
• Easy clean finish
• 2000mm high, 8mm thick
• Wall fixing profile supplied (chrome finish)
• Adjustable bracing bar supplied (1m, chrome finish)
• Sizes: 700mm, 760mm, 800mm, 900mm, 1000mm, 1100mm, 1200mm & 1400mm
• Adjustment for secure and easy fixing
• Optional floor to ceiling post available
• Optional floor channel available
• Life time guarantee
• CE Approved - Toughened 8mm thick glass
• European safety glass approved - EN12150-1<
